DS-5400A series

Frequency bandwidth 100-200MHz

Maximum Sampling Speed 2GS/s

(200MHz Type)

Maximum Sampling Speed 1GS/s

(100MHz Type)

Input Channel 4

Maximum Memory Length 500kpts/ch

All cycles captured from a waveform can be measured and displayed automatically. By taking in the data into the high length memory, you can observe the variability of Max/Min values and analyze the values from the calculation between the cursor intervals of time axis.

*Display one measured value per sweep on waveform parameter at vertical axis (voltage axis).

When an Iwatsu probe model is selected, the attenuation ratio and the coupling are set automatically. The model number, the band width of Vertical range, and Input coupling are displayed after you selected the model.

You can adjust the skews between the channels. This function is useful, for example, when you calculate the power waveform which is affected by timing.
Adjustment range of time difference between channels is Max. 500ns. When Preference to Skew is set at Horizontal axis (the numbers of waveforms of Replay function is limited.)

This function is used for Resetting the following calculated data:
REPLAY waveform, Averaging, Persistence, Auto-measure, Pass/Fail, Logging, and etc.

DS-5424A

DS-5422A

DS-5414A

DS-5412A

Frequency band (-3dB)

200MHz

100MHz

Rise time
(typical value)

1.75ns

3.5ns

Number of input channels

Four

2

Four

2

Maximum sampling rate

2GS/s (when channels are combined), 1GS/s (when all channels are used)

Equivalent sampling rate

100GS/s

Peak detection resolution

1 ns

Averaging function

2 to 256 times (power of 2)

Memory length

500k points/ch (all channels)

Vertical resolution

8 bits

Input voltage range

2mV/div ~ 10V/div

Offset voltage

2mV/div to 50mV/div: ±1V, 50.2mV/div to 500mV/div: ±10V, 502mV/div to 10V/div: ±100V

Deskew

0 ~ 500 ns

DC gain accuracy

± (1.5% + 0.5% full scale)

Maximum input voltage

±400 Vpk

Band limiting filter

Analog system: 20MHz, 2MHz, 200kHz

Input coupling

GND, DC 1MΩ, AC 1MΩ

Input impedance

1 MΩ ± 1.0% || 20 pF ± 2 pF (DC1 MΩ)

Probe sense

Automatic detection: 1:1、10:1、100:1、1000:1
Manual setting: 1:1、5:1、10:1、20:1、50:1、100:1、200:1、500 : 1, 1000:1, 2000:1

Time axis range

2ns/div ~ 50s/div

5ns/div ~ 50s/div

Standard probe

SS-0130R (Standard attachment for the number of channels)

Roll mode

50ms/div ~ 50s/div (100kS/s max)

Clock accuracy

±10 ppm

Trigger function

Trigger function

Edge, number of pulses, pulse width, period, missing, TV

Trigger mode

AUTO, NORMAL, SINGLE, STOP

TV trigger (standard) /
Line setting range selection /
Field selection

NTSC, PAL, Custom / up to 3000 / 1, 2, 4, 8

Pulse number trigger setting range

1 to 9999 events

Pulse width trigger time setting range

15ns ~ 50s

Period trigger time setting range

40ns ~ 50s

Dropout
trigger time setting range

50ns ~ 50s

Trigger source

All channels, EXT (±0.5V), EXT10 (±5.0V), line

Trigger slope/coupling

Positive, negative/AC, DC, high frequency rejection, low frequency rejection, noise rejection

Display/resolution

Display/resolution

7.5-inch color TFT LCD (touch screen) / VGA: 640 × 480 pixels

Display format

YT, XY, XY trigger

Vector connection

Interpolation display between sample points, dot display

Analog persistence

Monochromatic gradation display, spectrum display

Persistence display time

100ms, 200ms, 500ms, 1s, 2s, 5s, 10s, infinity

Internal waveform storage
(REF memory)

5 waveforms

AUTO SETUP function

Enabled/disabled configurable

Save front panel settings

5 settings can be stored in the internal memory, USB memory

Parameter measurement, cursor, zoom, calculation, replay function

Parameter measurement

Maximum value, minimum value, peak peak, RMS value, cycle RMS value, average value, cycle average value, top, base, top-base, rising overshoot, falling overshoot, rising time 20-80%, falling time 80-20%, rise time 10-90%, fall time 90-10%, frequency, period, number of pulses (positive), number of pulses (negative),
pulse width (positive), pulse width (negative), duty ratio , Integration, skew (positive/negative), skew @ level

Simultaneous measurement/statistical value display

Maximum 4 parameters/maximum value, minimum value, number of measurements

cursor

Time, amplitude, time & amplitude, cursor value

zoom

Press the Zoom button on the front panel to display the enlarged waveform in another grid

Math function

Addition, subtraction, multiplication, FFT
(up to 8k points, rectangular, Hanning, flat-top window function)

Rescale/Unit conversion

a*x+b (x: input voltage, a, b: user defined)/volt, ampere, watt, °C, no display

Replay

Automatically record waveforms, save up to 1024 waveforms, replay possible

Frequency counter

6 digits

interface

USB 2.0 HS compatible (device, host), GPIB (factory option DS-576)

AUX interface

External option connector

Save waveform data

Save to USB memory in binary, ASCII, Mathcad, Math (ASCII), Math (Mathcad)

Hardcopy output

Save to USB memory in TIFF, BMP, PNG (transparency compatible) format
or output image to PictBridge® compatible printer

Calibration signal output

Square wave 1kHz, 3Vp-p

Power/power consumption

AC100~240Vrms(50/60Hz), AC100V~120V(400Hz) / 95VA(60W)max

Dimension/Mass weight

About 330Wx190Hx124D mm / About 3.7kg

Environmental condition

Performance guarantee temperature

10 ~ 35 ℃

Operating temperature/humidity/altitude

Temperature 0-40°C / Humidity 5-80%RH ≤ 30°C (no condensation),
55%RH or less 40°C (no condensation) / altitude 2000m or less

Standard accessories

Probe (number of channels), power cord (1), front panel cover (1), instruction manual (CD-ROM) (1), user's guide (1)

option

GPIB interface
DS-576
(factory option)

GPIB: IEEE488.2

Power supply for probe
DS-579
(factory option)

Two power supplies for our active probe

DS-576

GP-IB interface

DS-579

Probe power option

IE-1226 made to order

VGA Video OUT option

You can output the waveform screen to an external display.

*DS-579 cannot be used after IE-1226 is installed.

Carrying bag

*Commercial item, multipurpose bag

SS-0130R

Frequency bandwidth: DC to 200MHz
Input RC: 10MΩ//12.5pF
Attenuation ratio: 10:1
Length: 1.5m

SS-320

Frequency bandwidth: DC to 100MHz
Attenuation ratio: 50:1
, 500:1 Maximum differential operating voltage: ±1400 V (DC+AC peak, 500:1
Total length: 2m

Standard price 99,800 yen (excluding tax)

DS-579

Probe power option

ViewGoⅡ dedicated probe power supply unit

Compatible probes: SFP-5A/4A, SS-270/260/250/240A/240, SS-320

PS-25

Power supply for SFP-5A/4A/SS-320

SFP-5A

Frequency bandwidth: DC to 1 GHz (for probe only)
Input capacitance: 1.9 pF
Input resistance: Approx. 1 MΩ
Attenuation ratio: 10:1

SFP-4A

Frequency bandwidth: DC to 800MHz  *1
Input capacitance: 2.15pF
Input resistance: About 1MΩ
Attenuation ratio: 10:1

DS-579

Probe power option

ViewGoⅡ dedicated probe power supply unit

Compatible probes: SFP-5A/4A, SS-270/260/250/240A/240, SS-320

PS-25

Power supply for SFP-5A/4A/SS-320

PHV 1000-RO

Attenuation ratio: 100:1, Input RC: 50 MΩ 7.5 pF
Frequency band: 400 MHz (for probe only)
Capacitance variable range: 10-50 pF, Length: 2 m

HV-P30A

DC-50MHz, DC-30kV, pulse 40kV

HV-P60A

DC-50MHz, DC-60kV, pulse 80kV

Rogowski coil current probe SS-28xA series

Frequency band: fL to 30MHz
Maximum peak current: 3,000A

Sensor part temperature range: -40℃ to 125℃

Rogowski coil current probe SS-29x series

Frequency band: S type-fL to 20MHz, L type-fL to 10MHz
Maximum peak current: 12kA

Sensor part temperature range: -40℃ to 125℃

SS-250

Frequency bandwidth: DC to 100MHz  *1  (maximum 30Arms)

SS-240A

Frequency bandwidth: DC to 50MHz  *1  (max. 30Arms)

SS-260

Frequency bandwidth: DC to 10MHz  *1  (up to 150Arms)

SS-270

Frequency bandwidth: DC to 2MHz  *1  (maximum 500Arms)

DS-579

Probe power option

ViewGoII series dedicated probe power supply unit

Compatible probe: SFP-5A/4A, SS-270/260/250/240A/240

PS-26

Power supply for current probe