WAVEFORMS
Standard sine, square, pulse, ramp, noise, sin(x)/x, exponential rise, exponential fall, cardiac, DC volts
¡@ ¡@
Arbitrary ¡@
Waveform length 1 to 64K points
Amplitude resolution 12 bits (including sign)
Repetition rate 1 µHz to 25 MHz
Sample rate 200 MSa/s
Filter bandwidth 50 MHz
Non-vol. memory Four (4) 64K waveforms
¡@ ¡@
FREQUENCY CHARACTERISTICS
Sine 1 µHz to 80 MHz
Square 1 µHz to 80 MHz
Pulse 500 µHz to 50 MHz
Arb 1 µHz to 25 MHz
Ramp 1 µHz to 1 MHz
White noise 50 MHz bandwidth
Resolution 1 µHz; except pulse, 5 digits
Accuracy ¡@

Stability

 ¡Ó 0.3 ppm, 18¢XC to 28¢XC
¡@ ¡Ó 1 ppm, 0¢XC to 50¢XC

Aging

¡Ó 1 ppm per 1 year
¡@ ¡@
SINEWAVE SPECTRAL PURITY
Harmonic distortion
¡@
≤ 3 Vpp1 > 3 Vpp
DC to 1 MHz 
 -60 dBc -55 dBc
1 to 5 MHz
-57 dBc -45 dBc
5 to 80 MHz
-37 dBc -30 dBc
¡@ ¡@
Total harmonic distortion
DC to 20 kHz < 0.2% + 0.1 mVrms
Spurious (non-harmonic)2
DC to 1MHz  -60 dBc
1 to 20 MHz -50 dBc
20 to 80 MHz  -50 dBc + 6 dBc/octave
Phase noise (30 kHz band)
10 MHz <-65 dBc (typical)
80 MHz <-47 dBc (typical)
¡@ ¡@
SIGNAL CHARACTERISTICS
Squarewave ¡@
Rise/Fall time < 8 ns
Overshoot < 5%
Asymmetry 1% of period + 1 ns
Jitter (rms) ¡@

< 2 MHz

 0.01% + 525 ps

≥ 2 MHz

 0.1% + 75 ps
Duty cycle ¡@

≤ 25 MHz

 20.0% to 80.0%

25 to 50 MHz

40.0% to 60.0%

50 to 80 MHz

 50.0% fixed
Pulse ¡@
Period 20.00 ns to 2000.0 s
Pulse width 8.0 ns to 1999.9 s
Variable edge time 5.00 ns to 1.00 ms
Overshoot < 5%
Jitter (rms) 100 ppm + 50 ps
Ramp ¡@
Linearity < 0.1% of peak output
Symmetry 0.0% - 100.0%
Arb ¡@
Min. edge time < 10 ns
Linearity < 0.1% of peak output
Settling < 50 ns to 0.5% of final value
timeJitter (rms) 30 ppm + 2.5 ns
¡@ ¡@
OUTPUT CHARACTERISTICS
Amplitude (into 50Ω) 10 mVpp to 10 Vpp
Accuracy (at 1 kHz, >10 mVpp, Autorange) ¡Ó 1% of setting ¡Ó 1 mVpp
Flatness (sinewave relative to 1 kHz, Autorange)

< 10 MHz

 ¡Ó 1% (0.1 dB)

10 to 50 MHz

 ¡Ó 2% (0.2 dB)

50 to 80 MHz

 ¡Ó 5% (0.4 dB)
Units Vpp, Vrms, dBm, high and low level
Resolution 0.1 mV or 4 digits
Offset (into 50Ω) ¡Ó 5 Vpk ac + dc
Accuracy 1% of setting + 2 mV + 0.5% of amplitude
Waveform Output ¡@
Impedance 50Ω typical (fixed) >10 MΩ (output disabled)
Isolation 42 Vpk maximum to earth
Protection short-circuit protected; overload automatically disables main output
¡@ ¡@
MODULATION
AM ¡@
Carrier waveforms sine, square, ramp, and arb
Mod. waveforms sine, square, ramp, noise, and arb
Mod. frequency 2 mHz to 20 kHz
Depth 0.0% to 120.0%
Source internal/external
FM ¡@
Carrier waveforms sine, square, ramp, and arb
Mod. waveforms sine, square, ramp, noise, and arb
Mod. frequency 2 mHz to 20 kHz
Deviation range DC to 80 MHz
Source internal/external
FSK ¡@
Carrier waveforms sine, square, ramp, and arb
Mod. waveform 50% duty cycle square
Internal rate 2 mHz to 1 MHz
Frequency range 1 µHz to 80 MHz
Source internal/external
External Modulation Input
Voltage range ¡Ó 5 V full scale
Input impedance 10 kΩ
Frequency DC to 20 kHz
¡@ ¡@
BURST
Waveforms sine, square, ramp, pulse, arb, and noise
Frequency 1 µHz to 80 MHz3
Burst count 1 to 1,000,000 cycles or infinite
Start/Stop phase -360.0¢X to +360.0¢X
Internal period 1 ms to 500 s
Gate source external trigger
Trigger source single manual trigger, internal, external trig
Trigger delay ¡@

N-cycle, infinite

 0.0 ns to 85.000 sec
¡@ ¡@
SWEEP
Waveforms sine, square, ramp, and arb
Type linear and logarithmic
Direction up or down
Start F/Stop F 100 µHz to 80 MHz
Sweep time 1 ms to 500 s
Trigger single manual trigger, internal, external trig
Marker falling edge of sync signal (programmable)
¡@ ¡@
SYSTEM CHARACTERISTICS
Configuration Times (typical)
Function change ¡@

Standard

 100 ms

Pulse

 660 ms

Built-in arb

 220 ms
Frequency change 20 ms
Amplitude change 50 ms
Offset change 50 ms
Select user arb < 900 ms for < 16K pts.
Modulation change < 200 ms
Arb Download Times GPIB/RS-232 (115Kbps)
Arb Length Binary ASCII Integer ASCII Real
64K points 48 sec 112 sec 176 sec
16K points 12 sec 28 sec 44 sec
8K points 6 sec 14 sec 22 sec
4K points 3 sec 7 sec 11 sec
2K points 1.5 sec 3.5 sec 5.5 sec
¡@ ¡@
TRIGGER CHARACTERISTICS
Trigger input ¡@
Input level TTL compatible
Slope rising or falling, selectable
Pulse width > 100 ns
Input impedance 10 kΩ, DC coupled
Latency ¡@

Burst

 < 100 ns (typical)

Sweep

 < 10 µs (typical)
Jitter (rms) ¡@

Burst

 1 ns; except pulse, 300 ps

Sweep

 2.5 µs
Trigger output ¡@
Level TTL compatible into 50Ω
Pulse width > 450 ns
Maximum rate 1 MHz
Fanout ≤ 4 Agilent 33250A¡¦s
¡@ ¡@
CLOCK REFERENCE
Phase Offset ¡@
Range -360¢X to +360¢X
Resolution 0.001¢X
External Reference Input
Lock range 10 MHz ¡Ó 35 kHz
Level 100 mVpp to 5 Vpp
Impedance 1 kΩ nominal, ac coupled
Lock time < 2 s
Internal Reference Output
Frequency 10 MHz
Level 632 mVpp (0 dbm), nominal
Impedance 50 Ω nominal, ac coupled
¡@ ¡@
SYNC OUTPUT
Level  TTL compatible into > 1 kΩ
Impedance 50 Ω nominal
¡@ ¡@
GENERAL
Power supply 100-240 V, 50-60 Hz / 100-127 V, 50-400 Hz
Power consumption 140 VA
Operating temp. 0¢XC to 55¢XC
Storage temp. -30¢XC to 70¢XC
Stored states 4 named user configurations
Power on state default or last
Interface IEEE-488 and RS-232 std.
Language SCPI-1997, IEEE-488.2
Dimensions (WxHxD) ¡@

Bench top

 254 x 104 x 374 mm

Rackmount

 213 x 89 x 348 mm
Weight 4.6 kg
Safety designed to EN61010-1, CSA1010.1, UL-311-1
EMC tested to EN55011, IEC-1326-1
Vibration and shock MIL-T-28800E, Type III, Class 5
Acoustic noise 40 dBA
Warm-up time 1 hour
Calibration interval 1 year
Warranty 3 years standard
¡@ ¡@
1 Harmonic distortion at low amplitudes is limited by a -70 dBm floor
2 Spurious noise at low amplitudes is limited by a -75 dBm floor
3 Sine and square waveforms above 25 MHz only with infinite burst count

Up | Next | Products list | brand | Model No. | Home